1.07.4
Compatibility
Changes
1.07.4
Cloud bases at the lifting condensation level. Every storm used to hang at Weather2's one fixed cloud layer, so a supercell over a swamp and one over a desert had the same base. A storm's base now sits at its lifting condensation level (LCL): the height where air rising from the ground cools to its dewpoint and its water condenses. It is read from the same heat and moisture as the rest of the air. Over a muggy plain or a swamp that is low, a few hundred metres, so the base hangs low and dark with a short, thick funnel under it. Over a dry savanna or desert it is two or three kilometres up, and the storm is high-based. The deck, the base the funnel ends at, the wall cloud and the rest of the storm all follow it, and the base eases up or down as a storm crosses from wet country into dry. It never comes closer than 56 blocks to the ground or goes higher than 280 above it. The new lclCloudBase setting (on by default) can switch it off to keep Weather2's layer.
A low base helps a storm put a tornado down; a high one starves it. Storm spotters treat a base below about a kilometre as favourable for tornadoes and one above about two as hostile, because under a high base the storm's rain-cooled air is too cold and dry to feed one. While deadly storms are decided by the air, a low LCL leaves the odds where CAPE and shear put them, and a high one cuts them to as little as a fifth (lclTornadoOdds, on by default). The forecast prints the LCL, the cloud base in blocks, the surface temperature and dewpoint, and what a spotter would make of them. The weather balloon reports its own LCL at launch, reads a dewpoint that closes on the temperature as it climbs, and radios when it rises through the cloud base.
Supercells built to a real supercell's proportions. Seen from a few hundred blocks off, a supercell read as a grey mushroom: a lumpy dark mass on a narrow rain column, a grey tower barely taller than the deck, and an anvil that sagged at mid-height like a second deck. It is now laid out from its own cloud base the way a real one is. The footprint is at least one and a half times as wide as the base is high. The rotating tower climbs nearly five times the base's height above it, as wide as a third of its height, white on its sunlit side all the way down and blue-grey on its shadowed side, with a hard, knuckled edge. Where it stops, the anvil spreads out flat and bright for at least twice the tower's height downwind, fanning out to about as wide as it is long, with an overshooting top punched through above the tower and rows of mammatus pouches sagging from its underside near the tower. The flanking line steps up toward the main tower in proportion to it. The tower's height is held inside your far clip plane, so it is not cut off at short render distances. The storm's own deck is now shaped as its base, broad and flat underneath and narrowing into the tower, instead of a cauliflower cap sitting on the rain shaft. The tower, anvil and overshooting top stay in full sunshine when you are standing in the storm's shadow, and they are shaded by the side turned toward you. Before, the darkened daylight under the storm dimmed them to the same grey as its base, and their shadowed far side showed through their sunlit near side.
A cleaner tornado up close. The funnel no longer flares so wide where it meets the cloud: its top was wider than the wall cloud and showed past both sides as two dark horns, so the tornado hung from what looked like the inside of a bowl. It now comes down as a slender column from a lowering that is always wider than it. The wall cloud sizes itself to take in the funnel where the funnel enters it, easing wider as a funnel grows, and its collar hugs the funnel. The hook of rain curling round the mesocyclone is drawn as rain instead of as dark puffs of cloud, and the dust the rear-flank downdraft throws out stays on the ground and fans out along it. Both used to hang in mid-air beside the funnel as floating dark balls. The debris cloud at the funnel's foot is built from more, smaller puffs, so it churns rather than breaking into separate dark lumps when rain muddies it.
A wall cloud you can see. A supercell's wall cloud was drawn as a spray of small dark puffs scattered at random inside a disc, each lasting a few seconds. That made a shape that reshuffled every moment and could not turn, and it sat up inside the storm's own cloud, where almost none of it showed. It is now a held block of cloud hanging well under the base where the funnel comes down, the way a storm spotter sees one: a flat dark floor, ragged near-vertical sides lit on the sun's side and shaded on the other, and the whole thing turning slowly, faster as the rotation tightens. A tail cloud streams into it at its own level from the rain of the forward flank, its air visibly running toward the wall cloud. As a tornado forms, a tighter collar drops out of its middle round the top of the funnel. It hangs about a third of the way from the base to the ground at full strength, and it grows and fades over a few seconds instead of snapping on.
No more blocky clouds flickering through storms with Sodium. With Sodium installed, the game's own flat clouds were drawn through every storm and spout cloud, as white slabs sliding across the soft clouds whenever you moved. This mod has always hidden the vanilla cloud layer, because the soft puffs do not write depth and the layer would otherwise be painted over them. Sodium draws clouds with a renderer of its own and switches vanilla's off before this mod's check could run, so the slabs came back. The layer is now turned off at the setting every cloud renderer reads, which covers Sodium's as well as vanilla's. A new hideVanillaClouds setting (on by default) brings the vanilla clouds back for anyone who wants them.
Projects on Modrinth are automatically available through a Maven repository for use with JVM build tools such as Gradle. To learn more about the Modrinth Maven API, click here.
Note: When available, you should use the creator's maven repo instead as it will have transitive dependency information that the Modrinth Maven API does not. You may also end up with duplicate dependencies if you use a mix of Modrinth and non-Modrinth Maven repositories for your dependencies, because the group identifier will be different when served through the Modrinth Maven API.
Maven coordinates:
Version ID:
build.gradle:
repositories {
exclusiveContent {
forRepository {
maven {
name = "Modrinth"
url = "https://api.modrinth.com/maven"
}
}
// forRepositories(fg.repository) // Uncomment when using ForgeGradle
filter {
includeGroup "maven.modrinth"
}
}
}
// Standard Gradle dependency
dependencies {
implementation "maven.modrinth:HfcD3g84:SL1mQ8l4"
}
// Legacy Loom dependency
dependencies {
modImplementation "maven.modrinth:HfcD3g84:SL1mQ8l4"
}

